By steven. Cupboard. At Wednesday, May 31st 2017, 12:26:23 PM.
Bathroom Design: Why You Should Incorporate Soft Close Draws and Cupboards in Your New Bathroom Soft close cupboard doors and soft close cabinet draws are two innovative and new products that can be incorporated into your bathroom design. They both are inexpensive design products, yet they have the look and feel of top end high priced products for your bathroom project. There is no need to purchase an entire new set of cupboards for your bathroom, as the soft close cupboard doors and soft close draws go right over our existing bathroom features. This is why they are less than remodeling and a whole lot easier as well. You dont need any fancy hinges, screws, or draw slides either as these products come with all you will need to spruce up your bathroom design. They are quick and simple to install and only take a few minutes and come with the complete and easy directions for your convenience. The soft close draw and soft close cupboard doors have been fully tested and are proven to be durable, so will last for years to come. These look great in your bathroom and keep your cupboards and drawers from slamming shut. No more pinched fingers or noisy problems. It also makes for less damage to your cupboards too. The Soft close draws will fit onto just about any brand of cupboard whether they are frame or frameless styles and fit right onto your old hinge in the upper section of the corner and attach instantly and smoothly in seconds. They are rated to uphold for more than 40,000 openings and closings, so you know they are going to last and last. They also have a lifetime guarantee as well, so you can feel good about adding them to your bathroom design project. When you start your bathroom design project, you need to order one soft draw pull for each drawer that is 22 inches or less and two for every one that is more than 22 inches. Thats all that is needed to make your old drawers as good as new and make them shut more smoothly and more quietly too. As for the soft close cupboard doors, you just need one for each door, so just count the number of doors and drawers in your bathroom cupboard and you are good to go for your next order. If you are unsure of how to install them, you can even watch videos online that will give you a step by step showing of how to put both products on in your bathroom. So, no matter if you merely are doing something to bet a bit of an updated look and feel in your bathroom or you are concerned about your children pinching their fingers or you just want a drawer or door that shuts more quietly, these great products are made to do the job for you with no trouble at all and not a great expense to your wallet either. So, be sure to order some of these soft close cupboard doors and soft close cabinet draws today to complete your next bathroom design product. Design Time Nottingham, the specialist for fitting Bathrooms Nottingham Design Time Nottingham, why not check out our Virtual Tour on our Google+ page Nottingham Kitchens
Pros and Cons of Kitchen Cupboard Resurfacing There are many benefits to having your kitchen, bathroom or office cupboards remodeled by resurfacing them. There are a few things that are not so good. My views on the pros and cons of renovating cabinets in this way come from thirty years of custom kitchen fabrication and home renovations. The process I will be discussing is recovering old Formica plastic laminate with new Formica. One of the most common questions people ask is; "does the old Formica get peeled off?" My answer is almost always; "no". The process involves roughing up the existing surface with sand paper and covering over the top of the existing plastic. Buying and Flipping Houses One of the things that I have noticed is that contractors, Realtors and people looking to make a few dollars from buying and selling houses, oftentimes will get estimates on resurfacing cupboards. Covering over the old laminate and installing new doors is a reasonably priced, quick fix way of remodeling an ugly kitchen or bathroom in comparison to installing new cabinetry. One of the BIG PROS of resurfacing is that a contract can be signed today and the cabinets be completed within four days. That is if there are not special order doors involved and the plastic laminate is available for next day delivery. Some Old Cupboards Still Have Wrinkles Even though your kitchen may get a face-lift on the outside, many things will still "mark" the cabinetry as being old. Things like water damaged areas around the sink, drawers that just dont move smoothly and dated materials used on the interiors of cabinets years ago will be noticeable. Even though the outside will look like brand new-the inside of the cabinets almost always show signs that they are older cupboards. How Good Will the New Surface Adhere? If your existing Formica laminate is adhered really well, then the chances of the new plastic staying secured to the old are really good. If you have several areas that are coming loose, then you will have problems down the road. Sure the installer can glue the loose areas down before gluing the new covering on top, but this is not going to stop the process of the old mica letting loose over the course of time. I would say that this is one of the biggest cons of recovering plastic laminate cabinets. Design Limitations What you see is what you get. There is not much that can be changed with an existing set of cupboards that are getting resurfaced. Sure, you can add a few drawers, maybe cut something down to make a new appliance fit and install a new cabinet or two, but the basic layout of the kitchen stays the same. Money Savings Comparisons There are several things that make kitchen cupboard resurfacing appealing to the home-owner seeking to remodel on a budget. For the most part, several thousand dollars can be saved. It is less expensive to resurface cabinets for several reasons: • Less materials are needed • Appliances do not need to be removed and re-installed • Electricians and plumbers may not be necessary • The amount of labor needed is a lot less when compared to fabricating a new set of cupboards In my experience, it seems like the pros and cons people get hung up on are the price savings and the design change limitations. They want to switch their kitchen cupboard layout a bit, but do not want to spend a lot of money for new cabinets. As previously mentioned, resurfacing does not allow for a lot of layout design changes. So, people have a tendency to find themselves stuck between a rock and a hard place. Very often, what happens in these situations is that the customer, rather than choosing to replace or reface, decides to wait until they can afford to get everything new.
Builders Tips - Fix Cupboards BUILT-IN CUPBOARDS Nearly every residence has some built-in cupboards and often we want more of them! Whether inside the kitchen, bedroom or bathroom, theyre usually in fairly constant use and so suffer the exact same wear and tear troubles suffered by doors and windows. Kitchen cupboards in particular break from constant opening and closing and being in contact with water and heat. Built-in cupboards could be one of the additional expensive things to call a tradesperson in to build. There are some jobs the average DIYer can do around the house to fix up difficulties and update the look of their built-ins. Kitchen cupboard doors no longer line up over time, cupboard doors tends to sag, particularly the ones that get used all the time. About once a year I need to take a screwdriver to the cupboard door hinges and fine-tune them to be able to keep the doors aligned. Most doors are designed to be adjusted rapidly and very easily with nothing more than a screwdriver, as most kitchens built inside the last 30 years or so have concealed, adjustable hinges. Usually these hinges have four adjusting screws, allowing you to make three main adjustments: Lateral - the front grub screw (or set screw) adjustment permits the door to be moved side to side. Depth - loosening the back screw enables the door to be moved in or out. Vertical - the two top and bottom screws enable for adjustment of the door in an up or down direction. Youll have to experiment with the readjusting to acquire ideal alignment, but you will soon get the hang of it. Its worth noting that most of these types of hinges are manufactured in Europe and will in all probability have Pozidriv screws in them. Fixing sagging corner cupboard doors The problem with built-in kitchens is the corner cupboard, It constantly ends up a black hole where you cant find anything thats pushed up the back, and the doors, being double Sectioned, usually sag and eventually fall off. This kind of hinged door is a lot heavier than your normal cupboard door, as the hinges on the cabinet and holds the combined weight of both doors, In order to counter this extra weight and open the gap between the top of the folding door as well as the adjacent door, you must compensate by over adjusting not only the hinges that attach the doors to the cabinet but also the hinges that join the two doors together. Both hinges will have an adjustment screw that fits via a slotted hole, usually at the back of the hinge assembly. Loosen this screw slightly and then push the two parts of the hinge closer together just before re-tightening. It could possibly take a couple of attempts to get the doors to sit where you would like them. Fixing drawers Just like the rollers on sliding doors, rollers on drawer runners can get worn or damaged. Replacing the inexpensive runners or slides will have the drawers rolling like new again and is really a fairly straightforward operation: 1 - Pull the drawer forward and lift the front to remove it from the cabinet. This will give you access to both parts of the roller assembly. 2 - Removing just a couple of screws will totally free up the old mechanism. Once again, a decent hardware store should have an exact matching assembly; if not, try cabinetmakers supplies in the phonebook. 3 - These are commonly sold in pairs and you must replace both sides of your drawer at once. You will only want a screwdriver to replace the old screws into the original screw holes. Sometimes with excess pulling and over loaded drawers (or perhaps if the runners had been broken), drawer front can turn out to be loose and pull away from the rest of the drawer. If this is happening to yours: 1 - Remove the drawers and clamp the front back into position. 2 - Add some tiny metal 90 degree angle brackets to the inside of the drawer prior to it comes apart entirely. Another common complaint is the collapse of the thin baseboard inside the drawer. This will normally take place for the reason that the drawer has been overloaded. Brad is a builder in Brisbane [http://www.brisbanehomebuilder.com]. Brad writes these articles in his spare time to share some of his building and DIY knowledge. For work Brad takes on home improvement building projects in Brisbane, Rockhampton and Townsville. These project include deck building projects, renovations and home extensions.