By steven. Cupboard. At Wednesday, May 31st 2017, 22:39:23 PM.
The Correct Way to Adjust Cupboard Hinges With Springs iam going to be giving you pointers on how to adjust your kitchen or bathroom vanity cupboard doors that have spring hinges? To recognize if you have this type of hardware, look at the edge of your door. If the mechanism is grooved into the edge of the panel and you can see metal on the exterior, then you have a Y-5 brand "SPRING" hinge. The Y-5 was designed to allow adjustments to be made in three different directions. Tools Needed: • Electric or Cordless Drill • 1/32" Drill Bit • Driver Bit With a Phillips Head • Phillips Screwdriver Take a very detailed look at all of your cabinet doors, paying close attention to what needs to be moved in which direction in order for things to look more uniform. If you have doors that are rubbing together it may be because they were originally made too large. In such cases, it may be necessary to have the doors cut down a little in order for them to close properly. Making the Hinge Adjustments Open a cupboard door and you will notice that there are four screws, two on the cabinet member and two holding the hinge fast to the door. One screw on the cabinet frame is a lock-down or "set" screw that doesnt allow for any adjustment. The other one is inserted into an oblong hole to allow for movement. The same is true for the hinge plate that is fastened to the cupboard door. Only remove the lock-down screw, then loosen the adjustment screw just enough to allow for the door to me moved a little. Leave enough tension on the hinge so that it can be moved, but is not "flopping" loose. Re-tighten the adjustment screw and close the door to see how things look. Continue this process of opening, adjusting and closing the cupboard doors until you are satisfied with your accomplishments. The alterations you are making should be very "minute" on each kitchen or bathroom door. You should relocate two doors by moving them a little rather than moving one door a lot. • Important: If a door is not resting on the face-frame of the cupboard correctly, never try to twist it by using the force of your hands. Always move the hinge plate on the inside of the cupboard frame toward or away from you, either at the top or bottom of the door. Once you are satisfied with your achievements, it is time to drill new holes for the lock down or "set" screws to be repositioned. While drilling these new holes, you will have to adjust the angle of the drill so you miss the original hinge set screw hole. It may be necessary to insert a few wooden toothpicks into the old holes. Be very careful to NOT drill through the cupboard door and ruin the decorative face. You can place a piece of tape on the drill bit to help you gauge how far you should drill. If you know how to make a stop-block, this would be a worthwhile procedure to undertake. Final Steps Tighten the set screws down and you are almost finished. If you need to adjust the location of the cupboard doors a little, its OK to tap them with the palm of your hand. There will be a little tolerance in the hinges even though the set screws are locked in place. Just be sure to NOT use excessive force. A slight tap here or there is OK. I always recommend hiring a professional cabinet maker to adjust cupboard hinges. There are always tricks in every trade that make things go smoother. You can try to do-it-yourself (DYI), but it has been my experience that most people just get frustrated and break something. Never the less, if you are the handy-man type, give it a try.
Builders Tips - Fix Cupboards BUILT-IN CUPBOARDS Nearly every residence has some built-in cupboards and often we want more of them! Whether inside the kitchen, bedroom or bathroom, theyre usually in fairly constant use and so suffer the exact same wear and tear troubles suffered by doors and windows. Kitchen cupboards in particular break from constant opening and closing and being in contact with water and heat. Built-in cupboards could be one of the additional expensive things to call a tradesperson in to build. There are some jobs the average DIYer can do around the house to fix up difficulties and update the look of their built-ins. Kitchen cupboard doors no longer line up over time, cupboard doors tends to sag, particularly the ones that get used all the time. About once a year I need to take a screwdriver to the cupboard door hinges and fine-tune them to be able to keep the doors aligned. Most doors are designed to be adjusted rapidly and very easily with nothing more than a screwdriver, as most kitchens built inside the last 30 years or so have concealed, adjustable hinges. Usually these hinges have four adjusting screws, allowing you to make three main adjustments: Lateral - the front grub screw (or set screw) adjustment permits the door to be moved side to side. Depth - loosening the back screw enables the door to be moved in or out. Vertical - the two top and bottom screws enable for adjustment of the door in an up or down direction. Youll have to experiment with the readjusting to acquire ideal alignment, but you will soon get the hang of it. Its worth noting that most of these types of hinges are manufactured in Europe and will in all probability have Pozidriv screws in them. Fixing sagging corner cupboard doors The problem with built-in kitchens is the corner cupboard, It constantly ends up a black hole where you cant find anything thats pushed up the back, and the doors, being double Sectioned, usually sag and eventually fall off. This kind of hinged door is a lot heavier than your normal cupboard door, as the hinges on the cabinet and holds the combined weight of both doors, In order to counter this extra weight and open the gap between the top of the folding door as well as the adjacent door, you must compensate by over adjusting not only the hinges that attach the doors to the cabinet but also the hinges that join the two doors together. Both hinges will have an adjustment screw that fits via a slotted hole, usually at the back of the hinge assembly. Loosen this screw slightly and then push the two parts of the hinge closer together just before re-tightening. It could possibly take a couple of attempts to get the doors to sit where you would like them. Fixing drawers Just like the rollers on sliding doors, rollers on drawer runners can get worn or damaged. Replacing the inexpensive runners or slides will have the drawers rolling like new again and is really a fairly straightforward operation: 1 - Pull the drawer forward and lift the front to remove it from the cabinet. This will give you access to both parts of the roller assembly. 2 - Removing just a couple of screws will totally free up the old mechanism. Once again, a decent hardware store should have an exact matching assembly; if not, try cabinetmakers supplies in the phonebook. 3 - These are commonly sold in pairs and you must replace both sides of your drawer at once. You will only want a screwdriver to replace the old screws into the original screw holes. Sometimes with excess pulling and over loaded drawers (or perhaps if the runners had been broken), drawer front can turn out to be loose and pull away from the rest of the drawer. If this is happening to yours: 1 - Remove the drawers and clamp the front back into position. 2 - Add some tiny metal 90 degree angle brackets to the inside of the drawer prior to it comes apart entirely. Another common complaint is the collapse of the thin baseboard inside the drawer. This will normally take place for the reason that the drawer has been overloaded. Brad is a builder in Brisbane [http://www.brisbanehomebuilder.com]. Brad writes these articles in his spare time to share some of his building and DIY knowledge. For work Brad takes on home improvement building projects in Brisbane, Rockhampton and Townsville. These project include deck building projects, renovations and home extensions.
Kitchen Cupboards Provide Strategic Storage Spaces and Harmony to Kitchens In the 21st century, the design and style of kitchen cupboards have evolved from large, solid types to lighter, more flexible and versatile ones. Today, you can see in many kitchens various wall cupboards positioned higher. Storage facilities are better now with the present lines of cupboards being offered in the market. Traditional cupboard dimensions are being modified by manufacturers and the possibilities are limitless. Your taste, budget and likes play important part in determining the style of kitchen cupboard you will end up with. So many brightly colored cupboards are out there made of exotic wood, modern plastic, stainless steel or aluminum to really arouse your desire. You can choose from a wide range of models to suit your needs. A tropical wood specie with laminated finish and stainless steel edging can truly wet your taste. There are granite countertops but if it is not within your budget, a granite looking laminated model is available. You can choose a totally custom-built look and shape or the traditional square with different handles to match your kitchen cupboards. But before you buy your new set of cupboards, concretize first your visualized kitchen cupboard design and objective. Everything depends on how you plan to organize and layout the kitchen cupboards you intend to buy. The kind of things you plan to store per drawer or shelves have to be decided in advance. Harmony and storage spaces are what you should aim for. If your kitchen is only small, think of all space saving strategies. If you inspect the things you store in your kitchen area, you will find many things which should be transferred and stored somewhere else. Make it your goal to provide more space for kitchen related items you need daily. Store in your cupboard shelves things which are commonly for kitchen use. Choose a compartment near the stove for pots and pans. You can try putting dishes on shelves in front near the cupboard doors for better access. If your kitchen is spacious, where you locate your cupboards to harmonize with the rest of the kitchen ambiance gives you a lot of options. You are not limited to items necessary for kitchen use only. In fact, the cupboards are functional in character but can be a pleasing sight for sore eyes. One way to have an organized cupboard system is to have a printed list of things inside each shelf or cupboard drawer for ready reference and faster accessibility. It may require constant revision but the beauty is you have always an updated inventory of all important and miscellaneous things stored in an orderly fashion. There are homeowners who have the inclination to repaint their kitchen cupboards for some reasons instead of ordering new ones and nothing is wrong with that. As a matter of fact, it is a noble project if they have the necessary technical skills. They can end up with brand new looking and more attractive kitchen cupboards with their high quality type of solid hardwood. By choosing the right type of color, finish and design edging mix and match, the repainted cupboards can enhance the beauty not only of the kitchen but also the rest of the house. Whether you decide to repaint your present kitchen cupboards or buy a new set, upgrading your kitchen with a new kitchen cupboard system will not only add value to your home but also provide a more convenient and better looking kitchen space for you to work in, relax and entertain!